Tag Archives: K1SWL

Midnight Design Solutions Phaser 20m FT8 Transceiver Kit Has Arrived

The week of December 9th 2019 I ordered one of Dave Benson’s K1SWL’s newest kit designs, Midnight Design Solutions Phaser, in the 20m version, along with an enclosure kit.

The kits arrived on January 10th 2020, earlier than originally predicted or expected.

Here is look inside a a Phaser:

Midnight Design’s Phaser FT8 Transceiver

These radios are single band designs, and the main FT8 frequency for the band is fixed, while an alternative frequency is defined but can be used modified. Actually it appears that the programming will work out of band, but the filtering & circuits not so much.

Continue reading

Tagged , ,

Midnight Design Solutions Phaser 20m FT8 Transceiver Kit Ordered

Last week I ordered one of Dave Benson’s K1SWL’s newest kit designs, Midnight Design Solutions Phaser, in the 20m version.

Excited about a kit that also catches the current fad of FT8 by design.

Ordered their neat looking enclosure kit as well.

I’ve built Dave K1SWL designed kits in the past with great success. He does a great job of builder-friendly designs.

Here is look inside a 40 or 80m build:

Midnight Design’s Phaser FT8 Transceiver

 

These radios are single band designs, and the main FT8 frequency for the band is fixed, while an alternative frequency is defined but can be used modified.

Continue reading

Tagged ,

Small Wonder Labs Retro-75 Kit Arrives and Project Start

The Retro-75 Board Kit has arrived this week. It came in two parts, everything but one component which arrived separately a few days latter (there was a note in the first package).

I’ve a satellite antenna project with my son Victor KC9NWB and a frequency reference for my shack to finish, both “on the bench” to complete first, putting the Retro-75 into a May build.

That will give me time to layout & source an enclosure, the second crystal socket & switch I will install and have those items on hand for the build.

My initial post on the Retro-75 is at: Going Retro on 75m AM – Small Wonder Labs Kit

I’m planning to shoot pictures and write something about all three projects as they go along.

73

Steve
K9ZW

Tagged , , , , ,

Going Retro on 75m AM – Small Wonder Labs Kit

Small Wonder Labs Retro-75 AM Transceiver

Small Wonder Labs Retro-75 AM Transceiver

Based on write-ups and recommendations from Scott NE1RD and Jeff KE9V, I took at look at Dave K1SWL’s newest offering “The ‘Retro-75’ 75/80 Meter AM Transceiver board kit.”

Although AM has long been supplanted by more effective modes of communication, AM activity is largely channelized into ‘watering hole’ frequencies2. It’s therefore pretty easy to find activity on the air. Here in the Northeast, 3885 kHz is the ‘hot spot’, and 3880 kHz is similarly used on the West coast.

Receiver:

The receiver front end is entirely conventional. …. Rather than wrestle with more stages of filtering or the use of ceramic filters, I reverted to a tried-and-true crystal filter. ……

The IF amplifier uses the so-called ‘cascode’ configuration…..

The following stage is a peak detector which serves to recover the modulation envelope from the received signal. Q3 is an ‘infinite-impedance detector’- a JFET biased near cutoff. I’d always wanted to say I’d used one- the phrase has a nice ‘Hitchhiker’s Guide’ ring to it…..

….

The audio output waveform is also peak-detected … and applied back …. as a form of Automatic Gain Control (AGC). Without it, nearby ‘Big Gun’ stations are easily capable of saturating this amplifier stage, yielding harsh-sounding clipped audio. …. With this feedback path in place, even the strongest of stations sounds fairly clean in the receiver.

Transmitter:

The RF strip consists of a crystal-controlled Colpitts oscillator, a FET-driver IC, and a MOSFET Power Amplifier stage. The PA stage runs class-C to keep the transmitter efficiency reasonably high. Generating an amplitude-modulated output is done using one of the oldest tricks in the book: the transmitter’s supply voltage is varied by superimposing audio on it through … an inexpensive 48Ω:3.2Ω audio output transformer. ….

In theory, this method is simplicity itself….. The transmitter runs about 2W of carrier power and 6-7W peak output. I ran key-down tests of up to a half-hour duration- they showed minimal transformer warming.

….

Receiver ‘Test’ function:

One of the impediments to building an L-C oscillator (here used as the receiver LO) is that component tolerances make the resulting operating frequency somewhat uncertain. CW/SSB projects can usually count on a borrowed signal from a ‘big rig’ in the shack to locate and adjust the local oscillator to frequency. With AM, though, there’s no ‘beat note’, and you’ll probably hear an ‘in-shack’ AM signal everywhere you tune. The circuit block labeled ‘Test’ provides a built-in frequency adjustment tool. …. (Quotes taken from Dave K1SWL’s Kit Instructions)

The Small Wonder Labs Retro-75 AM Transceiver Board Kit is so new it isn’t even linked from Small Wonder Labs Homepage and can be found at Small Wonder Labs Retro-75 AM Transceiver Web Page

It is listed in the ordering section of the main Small Wonders Lab Website.

I received a nice note from Dave K1SWL thanking me for my order. And I have to admit I am enthused to see it arrive; even more to do the build & get it on the air!

73

Steve
K9ZW

Tagged , , , , ,